Koffee Kosmo Roaster with Heat Gun as Alternative Heat Source

Koffee_Kosmo

You can fit a DIY diffuser nozzle under the plate to scatter the heat direction A lot easier than a new plate KK

bcspark

In the process of design of same .Will have to go to mates workshop to cut and weld 50mm SS hollow round. Just considering which will be better outcome for air supply

bcspark

Koffee Kosmo wrote:

You can fit a DIY diffuser nozzle under the plate to scatter the heat direction A lot easier than a new plate KK

Job done now heat is more centred and closer to beans.All I have to do now is roast ,rest and drink

bcspark

KK Have roasted two 600grm batches with the heat source 20mm above agitator post.The opening of the angled 40mm pipe begins at the post and back to the side of pot .This opening is cut horizontal to pot bottom giving a substantial opening.Both roasts have produced dark roasts around the centre which do not mix with the outer beans producing a mixed roast. Tested with 650grm of greens agitating ,dropped some dark beans into centre ,found the dark beans never left the top and centre . bcspark

Koffee_Kosmo

That's unusual ? However roasted beans will react differently when added to green beans - try painting some green beans red and test again I am wondering - If it did not do that before why is it doing it now? Just as a quick experiment - attach a dog type paper clip to the top of the agitator blade and observe what happens Beans may just need a kick along quicker due to extra heat concentration KK

bcspark

Never had this problem because the flow was directed to faster moving out side beans.Do you think I would be better to turn the nossle more to the outside. There has to be more agitation at the extremity compared to centre

Koffee_Kosmo

bcspark wrote:

Never had this problem because the flow was directed to faster moving out side beans.Do you think I would be better to turn the nossle more to the outside. There has to be more agitation at the extremity compared to centre

Yes there is more agitation on the outside The inside is the intermittent rest period where the beans dive down and work ther way slowly to the outside So it makes sense to aim the heat to the outside KK

bcspark

Koffee Kosmo wrote:

Yes there is more agitation on the outside The inside is the intermittent rest period where the beans dive down and work ther way slowly to the outside So it makes sense to aim the heat to the outside KK

Just completed test roast with heat directed toward outside problem fixed. Unbelievable that a small mod can upset the apple cart .Me thinks I will leave sleeping dogs lie and just enjoy roasting . Thanks KK

Koffee_Kosmo

bcspark wrote:

Just completed test roast with heat directed toward outside problem fixed. Unbelievable that a small mod can upset the apple cart .Me thinks I will leave sleeping dogs lie and just enjoy roasting . Thanks KK

Very good :thumb: Keep me in the loop on some future roasts to monitor consistency KK

bcspark

Did a test roast with a 45deg crank in the pipe eexstention .Found this slow roast down ,not delivering enough heat to bean mass. Conclusion is that the pipe exstention is to be straight ,meaning no flow restrictions to heat & air flow .Another test roast needs to be done but every body I supply are full up

bcspark

bcspark wrote:

Did a test roast with a 45deg crank in the pipe eexstention .Found this slow roast down ,not delivering enough heat to bean mass. Conclusion is that the pipe exstention is to be straight ,meaning no flow restrictions to heat & air flow .Another test roast needs to be done but every body I supply are full up

Used 100mm extention to HG, roast was ok but not enough control. Decided to go back to 50mm and found more control and available heat and fan . The resultant roasts were done to what I think is near perfection for a home roaster,CS8 226deg 16-17min. A

bcspark

bcspark wrote:

Used 100mm extention to HG, roast was ok but not enough control. Decided to go back to 50mm and found more control and available heat and fan . The resultant roasts were done to what I think is near perfection for a home roaster,CS8 226deg 16-17min.

For some unknown reason my reply was posted before I finished. To finish I now let the bean temp rise after preheat and load to ramp from bottom heat to 100deg to in 5min giving the bean time to dry and stabilize .From 100deg to target I apply 12-14deg/min

Koffee_Kosmo

I like the centralised heat distribution of the Turbo Oven If that pattern can be replicated I believe that you will be on a winner KK

Koffee_Kosmo

When I designed the central heat gun method ( I lost the drawing in a computer change ) I envisaged a Stailess Steel " turbo creating air deflector " just under the heat gun nozzil I will let out one small secret of the new KKTO design if it goes ahead - if not it will be published and be made available free to all If you search on the WWW for a Tornado Cyclone ( used in the car industry as an aftermarket accessory ) From memory it was invented by a Korean physicist and been around for couple of decades [attach=1] I feel that this product will distribute the heat that is best suited in the KKTO roaster design KK

galumay

Hey KK, which diameter cyclone did you think would work?

Koffee_Kosmo

galumay wrote:

Hey KK, which diameter cyclone did you think would work?

The largest dia @ approx 60mm would suit the standard KKTO KK

galumay

I have adapted my KKTO to take the HG2300E Steinel Heat Gun, its the straight type of heat gun and is rated for 2300W, 50-600deg C. It has sliders for incremental adjustment of fan and heat, i was going to use a Cyclone Vortex to distribute heat better, but initial trials show it to be so far superior to Turbo Ovens as is that I probably wont bother. First iteration is a fair hack of a job on an old TO, but it works and proved the viability of the option. Materials required beside the $400 heat gun were a bit of AlFoil, some high temp silicone, a coat hanger and a bit of hose! [attachimg=1] [attachimg=2]

galumay

The setup is amazingly controllable with the sliders, easy to replicate my TO profiles and i reckon it would roast 1KG easy, the sliders make it a dream to adjust on the fly, [attachimg=1] It looks to me like the nozzle of the Steinel has some sort of vortex doover anyway, [attachimg=2]

galumay

The first batch looked OK, (apologies for the out of focus image!) [attachimg=1] [attachimg=2]

Brett_H

Very nice mate! Now THAT'S a heat gun!

« Previous Page