Lever project - Urania 1 group

borat123

Who want's this one? 🙂 http://www.ebay.it/itm/MACCHINA-DA-CAFFE-FAEMA-A-GAS-DUE-GRUPPI-LEVA-PISTONE-/260868635247?_trksid=p5197.m7&_trkparms=algo%3DLVI%26itu%3DUCI%26otn%3D3%26po%3DLVI%26ps%3D63%26clkid%3D3443422840414039166

Lacehim

You might need to build that borat. You'll need another project, your nearly finished that one! Must be a record rebuild! Not that we are complaining.. it's been a great thread to watch. We might even have to organise a social event when you get it finished! 🙂

borat123

Hmmm, tempting, but my hands are pretty full right now, and the bank balance pretty low 😉 There's a Lambro (needs resto) going cheap as well...

borat123

I signed off on the artwork for the digital glass printing today. The colour will have more of a gold tint to it though..

Muscles

WOW, amazing working and at lightning fast speed! I can't wait to see the before and after photos side by side. What grinder will you have on the bench next to this beauty?

borat123

Good question... Nothing yet. I might have to get something modern, in the meantime to tide me over whilst looking for one to resto. If I could find one (unlikely), without paying a ransom (even more unlikely), then one of these would be nice to make a matching pair.. [the one on the left] But more likely, I've been sniffing around for one of these, which I think is a good match too...

Muscles

:o Wow! Just wow!

Koffee_Kosmo

There is one of those grinders for sale in Italy But it will cost you an arm and a leg http://www.ebay.com.au/itm/MACINACAFFE-FAEMA-FAEMA-GRINDER-/180735851652?pt=Macchine_del_Caff%C3%A8&hash=item2a14b23c84

borat123

KK, yep, that one's been relisted a few times. 1500 euro's is a bit optimistic.... :o Unrestored I've seen them starting at around 300 euro's. 🙂

Lacehim

So where's the Lambro? Where do you find these things?

borat123

The lambro's on Ebay france. Just keep looking. It all pops up sooner or later somewhere in Europe.

borat123

A quick question for the electrically non-challenged.... 😉 Are two piece heating elements normally wired in series? My old 1500W element has the bars running horizontally (A-B, and C-D), and a jumper connecting one leg of each (B-D). I dug out the multimeter and if I add together the resistance of each bar individually (A-B, + C-D), it equaled the resistance measured from the non jumpered terminal of each bar (A-C) confused? ??? Here's a pic of the old element, and a simple wiring diagram.... Any coments? (and yes it will be checked by an electrician)

borat123

AngerManagement wrote:

WARNING !!!!! DO NOT GET ANY OF THOSE TERMINALS WET !!! SAY AGAIN. DO NOT GET ANY OF THOSE TERMINALS WET !!! A: 1500W and 1500W at what rating ? B: What is the impedance of each one and in total..

Hi AM, the 1500W is total. The baseplate has 900W stamped on one side, and 500W on the other. Everything is still in parts at the moment, so no chance of anything getting near power just yet... 🙂 It was only partially soaked (lower than the baseplate) in citric acid to clean up the scale. I have a new element to replace the old one, as the copper is corroded in places and I thought it was likely suspect anyway. Measuring the old one: Impedance of the 500W is 94, and the 900W is about 55. Total across both was 150 Update edit: The new one which has slightly different element length measured 95, and 50, and is supposed to be 1500W. And here's a clearer pic of both the new and old:

Koffee_Kosmo

borat123 wrote:

Hi AM, the 1500W is total. The baseplate has 900W stamped on one side, and 500W on the other. Everything is still in parts at the moment, so no chance of anything getting near power just yet... 🙂 It was only partially soaked (lower than the baseplate) in citric acid to clean up the scale. I have a new element to replace the old one, as the copper is corroded in places and I thought it was likely suspect anyway. Measuring the old one: Impedance of the 500W is 94, and the 900W is about 55. Total across both was 150 Update edit: The new one which has slightly different element length measured 95, and 50, and is supposed to be 1500W.

I hate to say this But 900W + 500W = 1400 W KK

borat123

Yes yes KK, I failed primary school maths..... ;D ??? I forgot to clarify that the old one was 1400W, the replacement is 1500W because that's all there is.... Unless a custom job which is $$$.. PS. My 3mm, 0.5 pitch bolts arrived today: 😢 😢 Think they might have shipped me 2.0 or 2.5 by mistake.. I've also been looking around for 1/4" hard drawn copper tube, so I can make up a new fitting for the pstat. Seems to be rarer than hen's teeth.. Could probably use the soft annealed stuff from aircon / refrigeration but I prefer the firmness of the hard drawn.

borat123

Here's an updated wiring diagram. It turns out the element should be wired in parallel.

Koffee_Kosmo

borat123 wrote:

I've also been looking around for 1/4" hard drawn copper tube, so I can make up a new fitting for the pstat. Seems to be rarer than hen's teeth.. Could probably use the soft annealed stuff from aircon / refrigeration but I prefer the firmness of the hard drawn.

You just need to know where to look 😉 http://www.cranecopper.com.au/sizes/astmb88.asp KK

borat123

Thanks KK. Here's another one for you... ;D Anyone know an Australian supplier for chromed flexible gooseneck tubing? I want to use a couple of metres of it to carry the power cord. Something like this:

Koffee_Kosmo

borat123 wrote:

Thanks KK. Here's another one for you... ;D Anyone know an Australian supplier for chromed flexible gooseneck tubing? I want to use a couple of metres of it to carry the power cord. Something like this:

Most of that hose comes from overseas However the best and most economical solution is to use stainless steel braided hose Would a household under-sink type flex water hose work for you Or you can try this link http://www.ferret.com.au/c/Radcoflex-Australia/Corrugated-Metal-Hoses-Hose-Assemblies-and-Wire-Braid-by-Radcoflex-Australia-p22373 KK

borat123

Thanks KK. I'm trying to keep it the same as the original which I'm told was also used on the matching grinder. Here's something similar I found (the middle one): http://www.triflex.com.au/index.php?cPath=118_234_213 Waiting for confirmation on sizes available (limited availability if you're only buying 2 mtrs... 🙁 )

« Previous Page Next Page »