I'm building a KKTO for a member

Koffee_Kosmo

A Crema member contacted me by telephone after he visited Barazi - Bezzera Australia
He had a look at the demo model owned by Chris and offered money to buy it

But alas it was not for sale
We'll after a few phone calls and a little arm twisting I offered to make one

The preferred Arcosteel Pasta pot set was supplied
And to complete the build -
Some parts were used from the Koffee Kosmo shop
Parts that are no longer available were invented or manufactured with home tools and made to fit
Other items needed were purchased

For those that are interested - this thread will be a start to finish compilation of the build

Koffee_Kosmo

The first step is to drill the pots [attachimg=1] [attachimg=2]

Koffee_Kosmo

Then cut the high temperature insulation that sits under the false floor plate Afterwards cut the plate and use high temperature silicone to secure I used a DIY bush circle scribe to mark the circle line on the aluminium plate The roaster is designed to work best with a specific volume and by raising the pot floor one is reducing the volume [attachimg=1] [attachimg=2] [attachimg=3] [attachimg=4]

Koffee_Kosmo

Now it's time to start the base In this case I used what I had on hand - A circle of 25mm MDF I also purchased some caster wheels to fit on the underside of the base This serves as clearance for the motor that is to be fitted a little later on and for mobility I have also made the connector for the 12 Volt power supply And you will see some parts like the drive shaft and a dual agitator blade that I will fit and adjust to suit for coupling [attachimg=1] [attachimg=2]

Koffee_Kosmo

Ok the next step is to fit the drive motor and the wheels [attachimg=1] [attachimg=2]

Koffee_Kosmo

Then do the auto centre guides It's preferable to glue and let it dry before adding the screw [attachimg=1]

Koffee_Kosmo

While that's drying the next step is to cut and fit the high temperature tubes These tubes prevent heat escaping from 2 areas The join of the two pot sections and the coupling of the turbo oven You will also see that I have installed the agitator blade ready for testing and roasting [attachimg=1] [attachimg=2]

Trooper

Hi fellow members, I am a new member on this site, I was previously a member on another site which I will not mention. I would like to give a huge thank-you and praise to Paul (KK) in offering to make my KKTO. As I have a very sick wife at home who had a major stroke and could not find the time to build one myself, as I am her full time carer. What I have seen so far has absolutely impressed me. The workmanship that Paul has put into my KKTO is a credit to him. I have never been a person to heap praise on someone that I have only met once, but in Paul's case there is an exception. Thanks Paul, I can't wait to try it. :thumb:

derrilex

Welcome Gouly. :thumb: How come he gets the flash agitator and you give me the funny one ? :rofl:

Koffee_Kosmo

derrilex wrote:

Welcome Gouly. :thumb: How come he gets the flash agitator and you give me the funny one ? :rofl:

Three reasons 1) It's to big for your roaster insert 2) It's set up to lock onto the perforated insert ( yours is inverted ) 3) You are driving your roaster clockwise and it's my set up is anti clockwise KK

derrilex

A simple " because he is paying for it " would have sufficed 😃

Trooper

And he expects to pay for it too!!!!!

Koffee_Kosmo

Prior to finishing the next step all items were mocked up for good fit Then all attached items were removed and the MDF was sealed before final fitting as seen below Next step is to connect the 12volt wiring and connector All nice and neat :thumb: [attachimg=1] [attachimg=2]

Koffee_Kosmo

Add the security screws for the auto centre [attachimg=1]

Koffee_Kosmo

Testing the agitator action prior to its first roast [attachimg=1]

Koffee_Kosmo

Maiden roast of Gouly's roaster 700 grams of Colombian Bachue 18 [attachimg=1] Great results to second crack [attachimg=2] And the chaff collection works as it should [attachimg=3]

Trooper

Looks fantastic Paul, now the fun begins. :thumb:

Brett_H

Kudos Gouly on the new roaster. As always Paul... We are in awe of your talents.

Koffee_Kosmo

Brett H wrote:

Kudos Gouly on the new roaster. As always Paul... We are in awe of your talents.

My hope for this thread is to inspire others to build a KKTO roaster YES - Some DIY skills are needed however once built, one will have a great roaster design that will just roast beautifully thousands of times for its maker KK

derrilex

Result KK ! Roast looks tops. Enjoy Gouly :thumb: :thumb: